You can set the sort order of messages? Just click on the link in the date column. Your preferences will be remembered, so you don't have to do it again when you return.
Dear all ! I am trying to simulate a simple case of salt water instrusion. The model is configured in steady state for both flow and transport. I have also set...
Dear Giovanni, a groundwater model shows highly non-linear behaviour under density-dependent conditions. So if a model converges well with a density ratio of...
Hi Peter ! How are you doing? thanks a lot for the support you gave me for the other problem. theoretically, if I use steady state boundary conditions I would...
Dear all ! I am trying to import the pnt attached, in the section "reference data->observation single points->import points". When I do that the program does...
Giovanni, How did you import the files (from wich source). I used SHP files and I never had problem with it. What is your table structure ? Michael Verreault,...
Peter, thank you again for your support. I thought was possible to do that with pnt files too as I could import the labels during the construction of the...
Dear collegues, The 1st Circular of the 8th Hydrogeological International Congress of Greece & 3rd MEM Workshop on Fissured Rocks Hydrology, is ready and the...
Gerasimos Gioxas
yoxas@...
Jul 16, 2007 10:53 am
54
Hi to evrybody ! I tried to use the parameter estimator module to optimize the evaluation of the conductivities and I have succesfully run a model with it. The...
Hi Giovanni, FEFLOW does not save the optimal configuration. You can check the parameter set after the PEST run, and if you want to keep it just save the model...
Hi to evrybody ! Is there anybody who can explain me the results you can see in the attachment? (attachment not allowed in this group - Moderator) Could you...
Dear All! I am sorry for the last email. I have finally found the answer to my solution. When I run the modflow model I assigned a liner gradient along the...
I notice that my attachment was not allowed by Yahoo! Group. here you can find the picture I wanted you to see: http://bigfox.altervista.org/comparison.jpg ...
Hi ! I have a doubt . When I want to insert a well in a 3-d domain should I assign the disharge on the top or on the bottom of the well screen ? I thought it...
Dear all! I am sorry to bother you with my questions but as new user of this powerful program I am not able to understand some things. in this moment I am...
I am so glad I've found the group, since in Mexico, where I live is relatively unknown, so I inmediatly started to fill the registration. I am new in Feflow,...
Hi Giovanni, the pathlines you see are pathlines calculated on a 3D velocity field projected to the current slice. You don't see which ones leave the layer and...
Peter, another question: in the definition of the transport material I do not understand the meaning of "Porosity". Is it the total or the effective one? In...
August 3, 2007 Good Evening Hi! I would like to ask if how thus FEFLOW works. Because i'm doing my thesis about seawater intrusion on acquifers and my adviser...
Dear Sharlene, For details on FEFLOW, you can visit the website http://www.feflow.com/ You may also study the following paper/report/powerpoint presentation to...
Aug 5, 2007 Dear Kumar, Good Afternoon Thank you for the infos that you have give. I just want to know how to make a model (like to make the source code)?...
Dear Sharlene, I think, first of all, you must read any good book(s) on "Groundwater Modelling". To begin with, you can refer "Introduction to Groundwater ...
Sharlene, You find all the FEFLOW manuals on on http://www.wasy.de/english/products/feflow/doku.html Especially the Reference Manual and the White Papers Vol....
Dear all, Is there anybody who can help me to import a mesh in FEFLOW? I had previously generated a mesh with another program and now I would like to import it...
Hi averybody! I would like to know how to work in feflow with field data in order to calibrate the model... Could the programm automatically assign the flow...
Feflow is not like MODFLOW and don't allow to plot graph of simulated vs observed head. You have to export *.dar files in the postprocess of your model and to...
I guess borja in second question is talking about automatic calibration. Michael Verreault <michael.verreault@...> wrote: Feflow is not like MODFLOW and...
