You can set the sort order of messages? Just click on the link in the date column. Your preferences will be remembered, so you don't have to do it again when you return.
Dear Vivek, I would like this opportunity to put this forward to anyone in the group: How valid is simulating pumping in a 2D groundwater model ?, as a 2D set ...
Dear Redha You can do pumping test under in 2D modelling in axis-symmetrical mode when you really do not know much about aquifer parameters and hydraulic...
Dear Redha, I m completely agree with Yash Sir. We do 2D areal simulation modeling when we do not have the adequate data (T,S,head etc) of some layers under...
Am I suppose to email my forum postings to here? If so... I have a 3 layer model, which calibrate past 20m (Mean Residual). When I change parameters past the...
Sean Joseph Berry
s.berry@...
Jan 22, 2007 6:22 am
58
Dear Sean Can you expalin your problem in a bit detail? Yash Soil Scientist International Rice Research Institute-India ... From: Sean Joseph Berry...
The model area is approximately 5km N-S, 6km E-W. On the southern border of the model the area discharges along 4.8km of coastline. The lowest of the three...
Sean Joseph Berry
s.berry@...
Jan 23, 2007 4:20 am
60
Have you made a rough water budget for the area? You have to check that the water that run through (according to average transmissivity and gradient) is equal...
Hammarlund Elisabet
elisabet.hammarlund@...
Jan 24, 2007 4:20 am
61
Dear visual-modflow-group, I've problems with the left boundary condition of my model. I know the amount of groundwater (its just an estimation), which is the...
The specified flow (inflow) boundary condition may be simulated using injection wells at the boundary. Hope this helps. Regards, András Jakab Jakab és...
Jakab Andras
ajakab@...
Jan 24, 2007 11:50 am
63
It can be simulated by injecting the know amount (inflow) by installing injection wells (+ve flow). ************************************************* Dr Vijay...
Dr vijay Kumar
vijay@...
Jan 25, 2007 5:21 am
64
The program runs fine but I get "Project files are not accessible or corrupted" when I try to open 3D explorer. Project file is on the hard drive, and 3D...
Sean Joseph Berry
s.berry@...
Jan 31, 2007 4:11 am
65
Dear Sean, If you zip your project files and send them over to me, I will try to reproduce your problem (you may want to send a copy to my private account as...
Jakab Andras
ajakab@...
Jan 31, 2007 12:14 pm
66
Dear András, again, thank you for your kind offer. I have sent you the VMOD project, but in the process of zipping the file I needed to remove some of the...
Sean Joseph Berry
s.berry@...
Feb 1, 2007 3:25 am
67
I am in Delhi, and would like to know, the vendors from whom the vmodflow software can be purchased on limited tender basis, for a Govt organisation. Can...
Hello, first I have to say, that this group ist very usefull! Thanks! Here my question: I have problems with convergence by running the modell. Sometimes you ...
Hi all, Is there any option of exporting top, bottom, K, S, Rch etc in VMOD. I wish to export them in ascii (x,y,z) or in grid format. Regards, Hash...
syed hashmath
hashmath01@...
Mar 11, 2007 4:36 am
70
just go to the input section that you want to export, then file/export. It'll walk you through Best regards, Arne Springorum From:...
Dear Members, i am doing research on ground water optimization for coastal region. i need to optimize pumping rate, etc..,. so i want any GW optimization...
Hi members, I am working with Modflow since a couple of months and am actually using PMWin. Now i am working on this 3D-model which has 20 stressperiods (each...
Hi, I am just starting an introductory course in ground water modelling and will be using VISUAL-MODFLOW. Would you please suggest me of books/notes that I...
Philip, If you want to know how to use the program the user guide is very good, if you want to know something more about the finite difference method there...
Hi Dear Members I have some querries regarding the Visual modflow simulation. i found this group and i hope that i will get some guidance in this regard. 1.I...
Dear Member, I intend to prepare a directory of groundwater hydrologists. After compilation, I can upload the directory in the Files section of gwmodel group...
Dear Member, Based upon the information received, I have initiated preparing the directory of groundwater hydrologists. You can access the directory at ...
Hi Philip, Demo excercise/tutorial of VMOD would be of great help to beginners. I guess you can download this from WHI website. Hash. philip_kochumol...
syed hashmath
hashmath01@...
Jun 9, 2007 3:44 am
80
Date: Tue, 7 Aug 2007 09:33:41 -0400 (EDT) From: "elizabeth Philip" <philip_kochumol@...> Subject: Layer thickness To: gwmodel-owner@yahoogroups.com Hi,...
Hi Elizabeth is very easy.. Lo primero que puedes hacer es realizar para cada una de las capas es una malla de superficie en SURFER o en la version que tengas...
I'm trying to import a modflow 2000 dataset in Visual Modflow, created by the MF96to2k.exe tool. The original model was a modflow96 model created in PM Win. I...
hello i'm morroccan student in hydrogeology and I am a new user of visual modflow. I would like to have your opinion concerning how to calculate the quantity...
