Hello, I have a transport model in MT3DMS. From the results, I can plot the concentration contours. Also, from the mass balance, I can read the total mass of...
Head boundary conditions in Visual MODFLOW, provided that you are in layer view, are assigned layer by layer. In the Input menu select the Boundaries menu, and...
Jakab Andras
ajakab@...
Feb 13, 2008 7:15 am
99
Steady state model in modflow 4 layers high K, 1 river discharging the main system Not been able to calibrate targets successfully. The model sensitivity does...
Francisco Castrillon ...
franciscocastrillon.m...
Feb 14, 2008 3:44 am
100
Dear Member, Can you please refer me to any relevant literature (case studies/papers/web resources) pertaining to unsaturated and saturated groundwater flow...
Hello everyone. I need to modeling a electrokinetic process to removal heavy metals (Co and Cr VI) in shallow aquifer. But I don't know how to do this with...
Hello! I am trying to calibrate my model with one set of well observations and every time I try to run PEST, it says that the .hob file could not be opened....
Hi: it sounds as if your MODFLOW model is not executing correctly. Check the folder that you are running the model in for the presence of the .GLO and .LST...
Matt Tonkin
matt@...
May 16, 2008 3:23 am
104
Good Day !!! You are invited to join "Yahoo! Groups - archydro" (ArcGIS - Geographical Information System). This group aims to provide a forum for exchange of...
Hello, I have built a 3-layered model: quaternary sands on top of siltstone on top of sandstone. Now there are areas where layer1 (sand) does not exist. I do...
Dieter Plass
plass@...
May 22, 2008 12:10 am
107
This can be done by assigning properties to the particular cell (or number of cells) in first layer (sands) as that of second layer (siltstone). ...
Dr. Vijay Kumar
vijay@...
May 22, 2008 3:56 am
108
I can think in two options, but you must check the impacts of each one in the results of your model: 1) Import the terrain topography (1st layer top) and 1st...
Thanks for your feedback. I have looked into the manual again and it seems I have to apply a minimum thickness as it says that in Modflow layers must be...
Dieter Plass
plass@...
May 23, 2008 4:19 am
110
Hi, You cannot remove some cells in MODFLOW. Layers will cover the whole model area. What you can do is; assign the properties of layer above or layer below to...
syed hashmath
hashmath01@...
May 24, 2008 12:03 pm
111
If you implement option-2, you will have to be very careful in assigning recharge. Stela Cota <stelacota@...> wrote: I can think in two options, but you...
syed hashmath
hashmath01@...
May 24, 2008 12:04 pm
112
Hello, I am using Visual Modflow (4.2) along with Seawat to model some experiements conducted on saltwater intrusion. In the model scheduled pumping is carried...
Hello Albino, I think it's a typical Modflow problem (FD method): a dry cell is going to be dry for the whole simulation. Try to enlarge your cell height and...
Daniele Baldi
dbaldi@...
Jun 16, 2008 11:13 am
114
hello i m fresher for using modflow. can anyone tell me how can i start in modflow. what are the data requirements, what type of data is necessary for the...
hi, what version of modflow do you have? Regards, Reza ... From: shailendra sonekar <shailendrasonekar@...> Subject: [visual-modflow] how can i start...
Hello. I'm working in a model to evaluate the impact of a mine in the water supply of springs and rivers around the mine. My question is: what is better - put...
hello Shailendra, MODFLOW is a widely used software for groundwater flow modeling purpose. Required data for MODFLOW: - base map of study area - location of...
good morning first of all thanks for reply me,i m using modflow 4.0 version, its a demo version. ... From: reza saghravani <rezasaghravani@...> Subject:...
Hello Sonekar, Did you consider to take some course on Visual Modflow? Contact me on advancedgwt@... if you want. Dragan On Wed, Jun 18, 2008 at 6:53 AM,...
Hello Jeane, it depends on the size and flow of the springs and the connectivity with the aquifer. The main difference between river and drain packages is that...
Hallo Jeane, The drain boundary package in MODFLOW is designed to simulate the effects of features e.g. agricultural drain, which remove water from thw aquifer...
Dear Shailendra, if you want to use MODFLOW software to simulation groundwater flow or contamination, u need the below parameters in the first step. Parameter ...
Dear all, I am just new member. Now, I am doing research about mining that plan to use visual modflow to simulate in my study site. Could anyone ever train...
Maybe, it's a good start point. http://www.swstechnology.com/training_course.php?ID=8 ... Da: visual-modflow@......
Daniele Baldi
dbaldi@...
Jun 20, 2008 8:47 am
125
Hallo Jeane, The drain boundary package in MODFLOW is designed to simulate the effects of features e.g. agricultural drain, which remove water from thw aquifer...
